Table of Contents
Workbench
Cillian is doing woodwork in his Kindergarten and requested a Workbench for his 6th birthday. There was a proposal to buy one, but I thought that we could do better in building a proper one together. Time will tell the wisdom of this :)
Design
Stumbled on Roubo workbench projects from Christopher Schwarz, based on designs of André_Jacob_Roubo. I will try and implement some version of this.
- 5“ thick legs 2)
- 3½ thick top
- Recomended height - where your knuckles rub on surface (for me that is ~72cm) this allows you get your body mass over the part
- “Dog holes” along length of bench to clamp boards on surface with some type of end clamp
- “holdfast” iron clamp - bang down to hold, bang sideways to open.
- 3/4” dog holes (19mm)
http://benchcrafted.blogspot.de/2014/10/the-new-bench-plans-are-here.html
Materials
| Paid | Description | Dimensions | price |
|---|---|---|---|
| €17.12 | Rahmen Fichte - Spruce | 2m x 74mm x 74mm (3“x3”) | 2x €10,70 = €21.40 -20% |
| €12.80 | Rahmen Fichte - Spruce | 2m x 74mm x 44mm (2“x3”) | 2x €8 = 16€ -20% |
| €23.98 | Massivholzschwelle Douglassie - Douglas Fir | 2m x 240mm x 62mm (2½x9½“) | 29.98 -20% |
| €7.19 | Holzleim - classic | ||
| €4,78 | Glattkantbrett | 2m x 80mm x 18mm | |
| €2,18 | Riffelstab Buche - Dowel Beach | 2x 1m D=10mm | |
| €25€ (30$)| Hard white Maple 8/4 | 8x2" plank for leg vice | 6$ / BF |
For center Section:
Klenk Holz Rauspund Nadelholz gehobelt, getrocknet 2000 x 115 x 19 mm Packinhalt: 5 Stück (1 Bund) 1,15 m² Deckfläche: 1,1 m² Profilart: Nut + Feder €10.99
40mm thick board - with 15mm offset if you flip it over. 4)
Woodworking Handtools
| Description | Price |
|---|---|
| Doppelhobel 48mm - Wooden plane | €24.63 |
| Schreinerklufpfel - Mallet | €17.59 |
| Rücksäge 400mm | €16.99 |
| Wood Drill bits - 3-10mm | €7.99 |
| Mitrebox | €8.59 |
| Gliedermaßstab - measuring stick | €1.99 |
| Stechbeitel 6x Satz - Chisels | €68.07 |
| 2x Brass Dogs & 1x Wonderdog | €40.00 |
| 1x Holdfast | €20.00 |
| Auger Bits | €20.00 |
| Brace | €69.99 |
| Zwingen-Satz - Clamps | €11.98 |
| Schleifkork - sanding block | €3.18 |
| Spade Drillbits | $9.86 |
| Standard Waterstone 3 Stone Set | $89.99 |
| Watco Danish Oil - Quart | $12.99 |
| LN No.4 Brownze Smoothing plane | $350.00 |
| LN 20” Panel Saw - Rip 7tpi | $225.00 |
| Lie-Nielsen Honing Guide | $125.00 |
| DMT Dia-Flat Diamond Coated Lapping Plate | $195.00 |
| Jojoba Oil - 8 oz. | $12.00 |
| Panel Saw - Rip Cut 7tpi | $225.00 |
| Panel Saw - Crosscut 8TPI | $225.00 |
| Dovetail Saw | $125.00 |
| Carcass Saw | $140.00 |
| No. 60-1/2 Adjustable Mouth Block Plane | $165.00 |
| No. 62 Low Angle Jack Plane | $245.00 |
| Small Router Plane - Closed Throat | $80.00 |
| Tite-Mark | $89.00 |
| Boggs Flat Spokeshave | $135.00 |
| The Anarchist's Design Book | $45.00 |
| The Anarchist's Toolchest | $45.00 |
3/4“(19mm) hole - Veritas Wonderdogs 110mm (Brass - wire spring to hold in place) (wonderpup 60mm if bench is thinner than 2” - mine is bigger ⇒ wonderdog) Dog should be thicker than bench so you can push it up from below the bench
Need a hole all the way through the bench (else can use spring loaded “prairie dog”)
https://woodandshop.com/which-hand-tools-do-you-need-for-traditional-woodworking/
for tools https://www.feinewerkzeuge.de/
Wood Information
